Please use this identifier to cite or link to this item:
http://103.99.128.19:8080/xmlui/handle/123456789/617Full metadata record
| DC Field | Value | Language |
|---|---|---|
| dc.contributor.author | CHOWDHURY, SUVADRA | - |
| dc.contributor.author | ID:, 15MEE008P | - |
| dc.date.accessioned | 2026-11-18T03:58:06Z | - |
| dc.date.available | 2026-11-18T03:58:06Z | - |
| dc.date.issued | 2025-09-24 | - |
| dc.identifier.uri | http://103.99.128.19:8080/xmlui/handle/123456789/617 | - |
| dc.description | A Master of Science (M.Sc.) Thesis in Electrical and Electronic Engineering (EEE) Department at Chittagong University of Engineering and Technology (CUET). | en_US |
| dc.description.abstract | Research on microstrip patch antennas has increased noticeably over the last few years. Microstrip antennas present significant advantages and enhanced opportunities when compared to traditional antennas. They are lighter, occupy less space, are more cost-effective, have a lower profile, and are simpler to manufacture. Arrays enhance the overall gain, mitigate interference from specific directions, and optimize the signal-to-interference noise ratio (SINR). Arrays can be linear, circular, or planar. Planar arrays are remarkably versatile, with antenna elements arranged on a flat surface, yielding more symmetrical patterns with reduced side lobes and achieving much higher directivity. The focus of this research is to create a compact microstrip array antenna that employs a series-corporate feed dual-sided MIC network, aimed at functioning at a frequency of 10 GHz. Consequently, the primary target of this thesis is to create, analyze, and optimize a 2×4 microstrip array antenna. To explore this objective, the feeding distance of the 2×2 array corporate MIC feed on both sides (0.5λ, 0.55λ, 0.6λ, 0.65λ, 0.7λ, 0.75λ) is maintained consistently across patches, both horizontally and vertically, and networks have been developed. By incorporating four elements into a 2×2 array with series feeding, the design will be transformed into a 2×4 array with corporate-series feeding. A 2×4 array is designed using a corporate-series feeding technique; both the advantages of corporate and series feeding are obtained from this work. The corporate-series feed provided the highest gain and moderate transmission line loss among the three (series feed, corporate feed, and series-corporate feed). The project utilizes an inset feed line, which minimizes antenna size while enhancing gain, directivity, and the reflection coefficient. There is no requirement for impedance-matched transmission lines within the feed circuit. In this endeavor, a "both-sided" circuit technique is utilized, involving the arrangement of various categories of transmission lines on either side of the dielectric substrate, which is crucial for array antenna feed systems. Microstrip lines are positioned on the upper side of the dielectric substrate, whereas slot lines are situated on the reverse side. Through electromagnetic coupling, a novel feeding mechanism is developed. Previously, the array was a two-sided corporation. This array antenna has a two-sided series-corporate array (upper side and lower side) connected by a slot-microstrip and a v microstrip-slot branch line. Each patch element is connected by a 2.4 mm-width microstrip line in the whole network. This array structure is simple. It does not require structural changes through the use of stubs, transformers, multi-section transformers, taper lines, inductors, or capacitors. No impedance matching line is necessary throughout the complete feed system. Outstanding characteristics that significantly diminish undesirable cross-polarization have been verified. In particular, the advanced design system (ADS) developed by Agilent Technology, which is based on the method of moments, has been employed to confirm and assess the sizes of the suggested array antenna by utilizing the gain and directivity enhancement of antenna arrays. | en_US |
| dc.description.sponsorship | N/A | en_US |
| dc.language.iso | en | en_US |
| dc.publisher | CUET | en_US |
| dc.relation.ispartofseries | ;Tmail-19 | - |
| dc.subject | Microstrip Patch Antenna | en_US |
| dc.subject | 2×4 Microstrip Array Antenna | en_US |
| dc.subject | Series-Corporate Feed Network | en_US |
| dc.subject | Dual-Sided Feeding Technique | en_US |
| dc.subject | Corporate Feed Network | en_US |
| dc.subject | Antenna Array Design | en_US |
| dc.title | DESIGN OF A COMPACT MICROSTRIP ARRAY ANTENNA WITH SERIES-CORPORATE FEED BOTH-SIDED MIC NETWORK | en_US |
| dc.type | Thesis | en_US |
| Appears in Collections: | Thesis in EEE | |
Files in This Item:
| File | Description | Size | Format | |
|---|---|---|---|---|
| 24.09.2025_Tmail-19_Suvadra Chowdhury_15MEE008P.pdf | A Master of Science (M.Sc.) Thesis in Electrical and Electronic Engineering (EEE) Department at Chittagong University of Engineering and Technology (CUET). | 3.74 MB | Adobe PDF | View/Open |
Items in DSpace are protected by copyright, with all rights reserved, unless otherwise indicated.